HCJ-9201 dielectric oil dielectric strength tester
I. Overview
This product is based on the requirements of the International Electrotechnical Commission standard IEC 156 "dielectric oil dielectric strength measurement method" and the national standard GB 507-86, fully consider the needs of users at home and abroad based on a new model designed.
This machine uses digital display and locking technology, intuitive readings, high measurement accuracy; this machine takes into account the spherical, spherical cap, large flat panel, these standard electrodes used at home and abroad and small gaps of the small plate this non-standard electrode, enabling users A machine in hand, a variety of requirements have been met. This machine adopts special technology to provide special high-strength insulation transformer, which can supply 0-80kV maximum measurement range, small size and light weight. As long as the standard ground wire is reliable, the safety can be guaranteed; when the oil penetrates, the over-current protection is set Automatically cut off the power within 0.02 seconds; this machine is safe and reliable, and can fully meet the measurement requirements for the dielectric strength of various insulating oils.
HCJ-9201 dielectric oil dielectric strength tester
Main Specifications
1, the measurement range: 0 ~ 80kV maximum range measurement;
2. Power supply AC power supply: single phase 220V, 50Hz;
3, boost speed: 2kV/S±5%;
4, the electrode form: flat;
5, voltage distortion: <5%;
6, display accuracy: ± 1.5%;
7. Electrode clearance: small plate: 1.25mm, all of which are 2.5mm;
8, environmental conditions: temperature -10 ~ 40 °C, humidity is not greater than 75%;
9, the volume: 400 × 300 × 300mm 3 ;
10, weight: about 25kg.
HCJ-9201 dielectric oil dielectric strength tester
Instructions
(I) Preparation
1, the use of power supply for single-phase AC 220V, housing ground must be connected to the standard ground.
2, carefully install the inspection oil cup, pay attention to the axis of the two electrodes. Adjust the electrode spacing to a small plate: 1.25mm, the rest are 2.5mm.
3, close the power switch, power indicator light, at this time the voltmeter shows 00.0 that the machine is working properly. (The display shows that there are several word errors which are normal and do not affect the test accuracy.)
4, before step-up pressure must be reduced, and then for the boost test, otherwise refused to move.
(B) Test
1. Slowly inject the prepared oil sample into the oil cup, clean it twice, then fill it with the oil sample and place the oil cup on the electrode holder. Close the oil cup cover and press the interlock switch. (If you do not close the oil cup cover, it will refuse action).
2. Allow to stand for 10-15 minutes to eliminate air bubbles.
3. The boost switch can automatically raise the pressure. When the oil breaks down, the over-current protection relay and the protection system device act to cut off the power of the booster within 0.02 seconds. At this time, the figure shows the breakdown voltage of the oil. value.
4. To activate the step-down switch, the regulator will automatically return to zero and a second test may be performed after five minutes.
5. During the test, if the voltage of the outside line is insufficient, although the digital display does not reach 80KV, the regulator turntable has touched the limit switch.
6, in the test process, if there is an abnormal situation, you can press the stop switch to force off the high voltage power supply (retest, stop the switch reset).
Wire Cut EDM is fast, effective, and can be used to machining virtually any electrically conductive metal material, including Bronze, Copper, Tungsten, Carbon graphite, Carbon steel, Stainless steel, High alloy steel, Hard alloy, Inconel, Kovar, Titanium and many others. Computer-automated CNC equipment and advanced CAD/CAM programming guarantee our Wire Cut EDM to meet even the tightest tolerances.
We have been developed to prove an ideal mix of Speed, Accuracy, Surface Finsh and Low electrode Consumption.
Single Cutting Wire Cut EDM,High Speed Wire Cut EDM,CNC Wire Cutting EDM Machine,EDM Wire Cut
Jiangsu Sailing Intelligent Equipment Co., Ltd. , https://www.sailingcnc.com