Construction: The structure of lead batteries is mainly composed of positive (negative) plates, separators, electrolytes, tank shells, connecting bars and poles.
Role: It is a device that converts chemical energy into electrical energy and is a DC power supply. Its role is:
(1) When starting the engine, provide a strong starting current for the starter (generally up to 200~600A).
(2) When the generator is overloaded, it can assist the generator to supply power to the electrical equipment.
(3) When the engine is at idle speed, power the equipment.
(4) When the generator terminal voltage is higher than the electromotive force of the lead storage battery, a part of the electrical energy is converted into chemical energy to store it, that is, to charge it.
(5) The battery is a large-capacity capacitor that can protect the car's electrical appliances
Causes of battery damage
The battery life is generally about two years
1: excessive discharge
2: The battery is stored for a long time (without charging during storage)
3: Can't charge through car engine
4: No electrolyte
5: The proportion of electrolyte is too high
6: Charging at high temperatures
7: Contaminated by dirt (eg, contaminated with hydrochloric acid, seawater, organic acids, etc.)
8: The battery is charged with excessive current
9: The deformation of the electrode plate causes the positive plate and the pack plate to come into contact with each other, resulting in a short circuit
10: Dirt is deposited on the top and bottom of the pole, causing a short circuit
As long as you take care to avoid the above points, your battery life will increase accordingly.
Car battery maintenance and maintenance
(1) The electrolyte level should always be maintained between max and min. Check it once a month and see if the liquid level falls. Add distilled water (pure water) and do not add acid.
(2) When the battery voltage is insufficient and the light is dim and the starter is weak, the vehicle should be charged in a timely manner.
(3) To prevent the battery from overcharging or long-term loss of electricity. Overcharging will cause the active substance to fall off. The loss of electricity will cause the plate to vulcanize, and the regulator voltage must not be too high or too low.
(4) During use, exhaust vents should always be inspected to prevent battery deformation or burst.
(5) The battery should be kept away from heat and open flame, and should be ventilated during charging and use to prevent burns and injuries.
(6) To prevent long-term high-current discharge of the battery, the start-up time of each use can not exceed 5 seconds, and the time of two consecutive start-ups is 10-15 seconds in the middle.
(7) The battery must be firmly installed in the vehicle to reduce vibration.
(8) Always check if the battery cable is firm and all joints must be kept in good contact to prevent sparks and battery explosion. The oxides and sulphates produced by the battery clips must be scraped and painted with Vaseline to prevent further corrosion.
(9) Remove dust, dirt, and spilled electrolyte from the battery cover, and keep it clean and dry to prevent self-discharge.
(10) Cracking of the sealant should be promptly repaired.
(11) When the car is driving in a cold area, it is necessary to prevent the battery from being completely discharged to avoid freezing of the electrolyte.
ID starch pump is a horizontal, single-stage, cantilever Centrifugal Pump. Its rated performance characteristics and installation dimensions conform to the standard ISO2858, and its manufacturing technical conditions conform to ISO5199. This series of pumps absorbs the advantages of KSB pumps and WARMAN pumps. The improvement of the pump makes the solid content of the conveyed liquid up to about 50%. It is specially designed for the transportation of special media with high solid content, precipitation and easy crystallization, and fiber in the starch, sugar, food, pharmaceutical, chemical and other industries. Put an end to "running", "running", "leakage", "blocking" and other phenomena, China Starch Association "starch equipment localized first-class product".
The impeller design of the ID series pump is based on the solid content of the conveying slurry, whether it is crystallized and glued, the size of the solid particle size, and the length of the suspended fibers. The impeller can be designed to be closed and the flow channel is widened on the premise of not affecting the rated performance. , semi-open, open, swirling, etc., the seal can be designed as single-end or double-end mechanical seal, with impeller plus packing seal, plus impeller plus skeleton oil seal, etc.
Special Pump For Starch,Food Pump,Screw Pump,Food Transfer Pump
Jiangsu Qiantu Trading Co., Ltd. , https://www.qiantupump.com