·Wenzhou City can enjoy full subsidy for the early elimination of yellow label cars this year.

It was learned from Wenzhou Environmental Protection Bureau that from now until December 31, 2015, Wenzhou City will implement the Yellow Label Vehicle Subsidy Scheme, and the owners who apply for early elimination within this year can enjoy full subsidy.
It is understood that the yellow standard car refers to gasoline vehicles and diesel vehicles with lower exhaust emissions than national standards, excluding special vehicles, low-speed trucks, three-wheeled vehicles, motorcycles and wheeled self-propelled machinery. Qualified mark.
"This subsidy is applicable from today until the end of 2015. In 2014, when applying for early phase-out, the full subsidy standard will be applied. In 2015, the subsidy standard is about 70% of the full amount." Wenzhou Motor Vehicle Exhaust Han Jian, deputy director of the Pollution Prevention and Control Management Center, introduced.
It is reported that the scope of this subsidy applies to the yellow-label vehicles in Wenzhou City (Lucheng, Longwan, Bohai, Economic Development Zone), and the next step will be promoted in various counties. The owner can go to the “Green Wenzhou” website to check whether his vehicle belongs to the yellow standard car, meet the conditions of the portable ID card, the motor vehicle driving license, the yellow environmental protection inspection certificate issued by the environmental protection department, etc. to Wenzhou Zhennan Equipment Recycling Co., Ltd. The yellow label car “reduction subsidy application acceptance point handles relevant procedures.

Mixing Mill Manchine


Open rubber and plastic mixing is the rubber factory used to prepare plastic rubber, rubber or hot refining, a type of roller exposed rubber refining machinery. This machine is suitable for EVA,rubber,synthetic rubber,hot melt and all kinds of chemistry raw material to mix ,mediate and disperse, and then put into the mass production. It is the best choice to test, make sample and learning in school.

16inch automatic crusher mill

Advantage

1. The roller is made of chilled casting vanadium & titanium alloy iron which is hard and wear-resisting, the surface hardness is above 70degree, the surface coating is about 15mm.

2. Hard tooth gear reducer with well-design structure, low noise, high efficiency and long service life.

3. Self-aligning bearing is well matching with the bearing inside leakage-proof device. The sealers are made of high temperature,wear, oil resistance material,which have very good sealing effect.

4. All main electrics are imported, the alternating current contactor is Shilin brand. The switch and button are Taiwan Tend brand.

5. Circulating lubrication system solves the oil leakage problem. The feature of this system is easy to maintain,easy to replace.

6. This machine is installed with overload protection device which protect the machine will not broken if the machine is overload. The machine will reverse 1/3 round when press the emergency stop button,which sure the production safety.

7. The [U" shape frame is whole set casting, but other factory welded together.

8. The machine base is welded by national standard I steel.

Main parameter

Name

A Automatic crusher mill

Front roller diameter (mm)(Smooth roller)

400

Rear roler diameter (mm)(Groove roller)

450

Roller length(mm)

840

Front roller speed (m/min)

12.67

Speed ratio

1:1.63

Max roller gap(mm)

10

Nip adjustment

Manual

Mixing capacity(kg)

20

Power (kw)

45-8

Motor RPM(r/min)

740

Reducer ratio

45

Reducer model

315

Roller bearing diameter(mm)

260

Bearing mode

352952YA

Bearing size(mm)

360×260×150

Name

B mixing mill

(mm) Front roller diameter(smooth roller)

400

Rear roller diameter (mm)(smooth roller)

400

Roller length(mm)

840

Front roller working speed (m/min)

19.36

Speed ratio

1:1.5

Max roller gap(mm)

10

Nip adjustment

Manual

Mixing capacity(kg)

20

Power (kw)

37KW

Motor RPM(r/min)

980

Reducer ratio

45

Reducer model

315

Roller bearing diameter(mm)

260

Bearing model

352952YA

Bearing size(mm)

360×260×150


Mixing Mill Manchine,Open Mill,Rubber Mixing Mill,Roller Mill

SHIJIAZHUANG LONGXUAN TRADING CO., LTD , https://www.longxuanmachine.com